There are several methods that are used for upper cabinet installation. I have thirty years of experience in installing kitchen cupboards. These techniques have proved to be the easiest way for me to hang uppers on the walls. These tips on Cabinet Installation Orem UT will save you hours of frustration if you use them.
One of the first steps is to find where the studs or furring strips are located. I do this by tapping on the drywall with my knuckles first. After I find a location where I think there is one, I begin drilling three-sixteenths inch holes in various places. These holes should be drilled in an area where the cupboards will cover them up once they are installed. When I hit the stud, I mark it. Next, I measure over sixteen inches from the mark and tap on the wall again looking for the next stud. Repeat the process until all of them are located and marked.
Attention to detail- The measurements have to be taken accurately and the molding has to be perfect. Every little detail counts and the materials that you use should be of good quality as well. It is also very important to hire the services of a good kitchen cabinets installation company. Since they specialize in these jobs, they know how to deal with the little glitches that can come up in the course of the work.
Before you drill holes in the wall, ensure that you have the correct measurements and that the precise location that you are drilling in has adequate support at the back. This is particularly important when the wall is not made of concrete and has a hollow wall. A cabinet that is screwed with insufficient support will easily fall with the additional weight of some very heavy kitchenware like the pressure cooker.
Make Sure the Floors Are Even- Next, check to see if your floors are even. You can do this by using a traditional level, but most installers recommend that you use a laser level to ensure the floors are completely even. Level floors are important because there may be gaps in some areas of the new cupboards if sections of the floor are too low. On the other hand, you may not be able to fit them in properly if the floor slopes unevenly.
Bore three-sixteenths inch wide pores in the back of the initial drawer corresponding in the same locations as where the studs are located on the wall. Place the prop sticks on an angle, slightly below the level line. Hoist the first top drawer up to the level line and move the props so that they support the weight of the cupboard. Hold the drawer steady and secure it to the wall with number two screws.
Move the props over to support the next wall cupboard to be installed. Drill the drawer back in the locations where the screws will sink into the wall studs. Hold the upper in place, adjust the props to hold it up and then use clamps to align the cupboard face with the first wall drawer you installed. Secure the clamps very tightly. Fasten the drawers together in the front first, and then secure the drawer to the wall.
Continue the process until all of the cabinets are installed. These installation tips should serve you well. The most important thing to remember is to install all of your cupboards levels and tight to the walls and ceiling.
One of the first steps is to find where the studs or furring strips are located. I do this by tapping on the drywall with my knuckles first. After I find a location where I think there is one, I begin drilling three-sixteenths inch holes in various places. These holes should be drilled in an area where the cupboards will cover them up once they are installed. When I hit the stud, I mark it. Next, I measure over sixteen inches from the mark and tap on the wall again looking for the next stud. Repeat the process until all of them are located and marked.
Attention to detail- The measurements have to be taken accurately and the molding has to be perfect. Every little detail counts and the materials that you use should be of good quality as well. It is also very important to hire the services of a good kitchen cabinets installation company. Since they specialize in these jobs, they know how to deal with the little glitches that can come up in the course of the work.
Before you drill holes in the wall, ensure that you have the correct measurements and that the precise location that you are drilling in has adequate support at the back. This is particularly important when the wall is not made of concrete and has a hollow wall. A cabinet that is screwed with insufficient support will easily fall with the additional weight of some very heavy kitchenware like the pressure cooker.
Make Sure the Floors Are Even- Next, check to see if your floors are even. You can do this by using a traditional level, but most installers recommend that you use a laser level to ensure the floors are completely even. Level floors are important because there may be gaps in some areas of the new cupboards if sections of the floor are too low. On the other hand, you may not be able to fit them in properly if the floor slopes unevenly.
Bore three-sixteenths inch wide pores in the back of the initial drawer corresponding in the same locations as where the studs are located on the wall. Place the prop sticks on an angle, slightly below the level line. Hoist the first top drawer up to the level line and move the props so that they support the weight of the cupboard. Hold the drawer steady and secure it to the wall with number two screws.
Move the props over to support the next wall cupboard to be installed. Drill the drawer back in the locations where the screws will sink into the wall studs. Hold the upper in place, adjust the props to hold it up and then use clamps to align the cupboard face with the first wall drawer you installed. Secure the clamps very tightly. Fasten the drawers together in the front first, and then secure the drawer to the wall.
Continue the process until all of the cabinets are installed. These installation tips should serve you well. The most important thing to remember is to install all of your cupboards levels and tight to the walls and ceiling.
About the Author:
If you are looking for the facts about cabinet installation Orem UT residents should come to our web pages today. More details are available at http://www.daltonscabinets.com/products now.